图片提示词案例
实战案例:用AI提示词生成跑鞋中底科技拆解图,从发泡颗粒到5版迭代
发布时间:2026年11月19日 08:23:00以一款超临界发泡中底跑鞋的科技页主图为真实场景,演示如何用 Flux 制作「爆米花颗粒 + 碳板 + 半透明气垫」的三层拆解图,重点解决剖面结构的合理性、颗粒尺度的统一、材质之间的透光差异,以及爆炸视图的排列秩序。
背景
需求来自一家国产跑鞋品牌:科技页要一张中底拆解图,把「超临界发泡 + 碳板 + 气垫」三层结构讲清楚。
这类图的难点和普通产品图完全不同:
- 剖面必须合理:结构错了,懂行的人一眼看穿;
- 颗粒尺度要统一:发泡颗粒忽大忽小就假;
- 透光差异:气垫是半透的,泡棉是不透的,碳板是反光的;
- 爆炸视图有秩序:三层要沿同一轴线分开,间距一致。
工具用 Flux。
第一步:先定结构,再谈质感
写提示词前先画一张结构草图,明确三层的中文名与英文描述:
| 层 | 结构 | 英文锚点 |
|---|---|---|
| 上层 | 超临界发泡泡棉 | supercritical foamed midsole, bead-based |
| 中层 | 全掌碳纤维板 | full-length carbon fiber plate |
| 下层 | 后跟气垫 | rear heel air unit, translucent |
Exploded view of a running shoe midsole, three layers separated along
a single vertical axis with equal gaps: top layer is supercritical
foamed midsole, middle layer is a full-length carbon fiber plate,
bottom layer is a translucent heel air unit. All three layers share
the same outline shape, aligned center to center.
踩坑一:V1 没有写「同一轴线、间距相等」,三层被摆成斜的,还错位。加 aligned center to center + equal gaps 后才规矩。
第二步:发泡颗粒要有统一尺度
超临界发泡的特征是均匀细密的泡孔,不是大颗爆米花。
The foam surface shows uniform closed-cell beads, roughly one millimeter
across, densely packed with no large voids. The cut edge reveals the
same bead structure inside, consistent in size from heel to toe.
No large popcorn-like lumps, no visible seams, no melted look.
三个要点:
- 1 毫米:量化尺度;
- 剖面同样结构:内外一致才可信;
- no melted look:防止渲染成发泡胶。
踩坑二:V2 的剖面内部是实心的一块,只有表面有颗粒。加上「cut edge reveals the same structure」之后,剖面才有工艺感。
第三步:三层的透光与反光必须分开写
Material response differs by layer: the foam is fully opaque and matte,
absorbing light; the carbon plate is glossy with a woven twill pattern
and a sharp specular highlight along its edge; the air unit is
translucent, slightly blue-tinted, transmitting soft light with a
visible inner membrane.
关键判断:透光、哑光、反光三种反应必须同时出现在一张图里,这正是「科技感」的来源。
踩坑三:V3 三层的材质反应几乎一样,全是哑光塑料感。分开写之后,气垫透亮、碳板反光、泡棉沉闷,层次立刻出来。
第四步:爆炸视图的排列秩序
Clean studio layout: pure light grey background, no props, no text,
no arrows. The three layers float with soft contact shadows on nothing,
each casting a faint shadow on the layer below. Slight three-quarter
view from the front-left at 30 degrees. 85mm lens, f/11, everything sharp.
三条:
- 背景纯浅灰:科技页需要干净底色;
- 层间投影:靠投影建立前后关系;
- 30 度俯视:既能看厚度,也不失真。
踩坑四:V4 用 45 度俯视,气垫被压扁看不出体积。改 30 度后厚度关系正常。
第五步:五版迭代
| 版本 | 改动 | 结果 |
|---|---|---|
| V1 | 只写三层结构 | 排列错位,结构模糊 |
| V2 | 加轴线与等距 | 排列规整,颗粒过大 |
| V3 | 量化颗粒 + 剖面一致 | 工艺感出现,材质雷同 |
| V4 | 分开写透光/反光 | 层次成立,透视过陡 |
| V5 | 改 30 度 + 加层间投影 | 最终版 |
V5 还删掉了一样东西:原计划的箭头标注。AI 画的箭头必然歪,后期加上去反而更省事。
成果与复盘
最终主图用于科技页首屏,另裁 1:1 用于详情页模块。
复盘最有用的一条:拆解图的关键不是「好看」,而是「每一项参数都能对上」。颗粒 1 毫米、三层等距、同一轴线,这些数字决定了图能不能被当作技术说明使用。
成本拆解:
| 项目 | 支出 |
|---|---|
| Flux 生成(约 90 次抽图) | 约 68 元 |
| 后期(结构校正、箭头标注) | 约 420 元 |
| 合计 | 约 488 元 |
6 条可复用清单
- 先写结构再写质感:三层名称、轴线、间距先定。
- 颗粒量化到毫米:1 毫米闭孔,比「细腻」有效。
- 剖面内外一致:cut edge 要露出同样结构。
- 三种材质反应分别写:透光、反光、哑光。
- 层间投影造前后关系:爆炸视图靠影子分层。
- 箭头和文字交后期:AI 画标注必然歪。